10V 10000A RECTIFIER
Mak Plus Power Systems design and produce many different kinds of rectifiers in Germany or Europe for various purposes. Depending on your needs and choice, we offer you three different kinds of cooling for our rectifiers: Air, oil or water cooling. A selective working program for 10V 10000A rectifier is offered by Mak Plus Germany. Commonly, a selective working program is using in order to remove unwanted metals from most of the plating pools, but this process has to be done either manually or with an external device. Mak Plus Power Systems Germany provides you this process is done automatically, using the selective program with MRS plating rectifiers (10V 10000A). When the operator starts the process, the output voltage keeps increasing from zero, and then turns back to zero again. This process can be repeated indefinitely or for a limited time according to your needs and wishes. This way, you can spare your work force.
Our rectifiers 10V 10000A that we offer you as Mak Plus Power Systems , the rectifier as 10V standard plating and galvanizing rectifiers that run with a very user friendly interface. With the remote control, the operator can run the device from a distance. The operating system is fully compatible with all automation systems that run manually or with an automation system. The galvanizing rectifier identifies the surface of the component automatically and calculates the needed operation time for the desired thickness. The operator only has to enter the value of the desired thickness and push the start button. It is as easy to use as can be. All the other processes are done by the rectifier itself automatically. Input voltage values can vary between 230V / 380V / 415 V / 480 V AC and 50Hz or 60Hz for 10V 10000A rectifier.
Our rectifiers 10V 10000A that we offer you as Mak Plus Power Systems , the rectifier as 10V standard plating and galvanizing rectifiers that run with a very user friendly interface. With the remote control, the operator can run the device from a distance. The operating system is fully compatible with all automation systems that run manually or with an automation system. The galvanizing rectifier identifies the surface of the component automatically and calculates the needed operation time for the desired thickness. The operator only has to enter the value of the desired thickness and push the start button. It is as easy to use as can be. All the other processes are done by the rectifier itself automatically. Input voltage values can vary between 230V / 380V / 415 V / 480 V AC and 50Hz or 60Hz for 10V 10000A rectifier.
10V 10000A Rectifier for Galvanizing
With air cooling, oil cooling and water cooling options |
You can download 10V 10000A rectifier datasheet below: |
Our galvanizing rectifiers ( 10V 10000A) use a recipe system, therefore the operating system keeps a record for every aluminum component with different characteristics. These records can be used as a recipe for different components as well. Therefore the process can start faster. This also ensures a standardized production. It also minimizes possible conflicts that can occur between different recipes.
There is a timer inside these rectifiers (10V 10000A) ,which enables you to set it to work for either a limited time or continuously. When it is set to work for a limited time, 10V 10000A rectifier works until it reaches the desired values and then it stops automatically. At the end of the process, the operator gets a warning. When it is set to work continuously, the rectifier keeps functioning normally until the operator interrupts the process when it’s desired to. Pool temperature is measured by 10V 10000A rectifier and shown it on the panel. Therefore your operator doesn’t need to check the temperature of the pool manually or using an external device. This saves work force and time. An anodizing bath should be between 18 – 22 Grads Celsius. These minimum and maximum temperature values are on the system. 10V 10000A rectifier measures the pool temperature and checks its conformity to the given values, and then runs the cooling system if needed. 10V 10000A rectifier stops when it reaches the desired temperature, so that there won’t be any need for complex temperature control mechanisms.
As Mak Plus Power Systems, the rectifiers we offer are equipped with the latest AC power control unit. This unit ensures that the chances of malfunction are minimized and it also increases the functions of the rectifier. With this new AC drive unit, the possible errors are prevented even before they occur. Therefore these galvanizing rectifiers can endure even the most difficult of circumstances without being concerned about problems that can occur about safety. The new drive system can work with a remote control and it has an automation system.
Our galvanizing rectifiers can be used in the areas below:
There is a timer inside these rectifiers (10V 10000A) ,which enables you to set it to work for either a limited time or continuously. When it is set to work for a limited time, 10V 10000A rectifier works until it reaches the desired values and then it stops automatically. At the end of the process, the operator gets a warning. When it is set to work continuously, the rectifier keeps functioning normally until the operator interrupts the process when it’s desired to. Pool temperature is measured by 10V 10000A rectifier and shown it on the panel. Therefore your operator doesn’t need to check the temperature of the pool manually or using an external device. This saves work force and time. An anodizing bath should be between 18 – 22 Grads Celsius. These minimum and maximum temperature values are on the system. 10V 10000A rectifier measures the pool temperature and checks its conformity to the given values, and then runs the cooling system if needed. 10V 10000A rectifier stops when it reaches the desired temperature, so that there won’t be any need for complex temperature control mechanisms.
As Mak Plus Power Systems, the rectifiers we offer are equipped with the latest AC power control unit. This unit ensures that the chances of malfunction are minimized and it also increases the functions of the rectifier. With this new AC drive unit, the possible errors are prevented even before they occur. Therefore these galvanizing rectifiers can endure even the most difficult of circumstances without being concerned about problems that can occur about safety. The new drive system can work with a remote control and it has an automation system.
Our galvanizing rectifiers can be used in the areas below:
- Electro-plating
- Catastrophes Paint
- Anodizing Plating
- Aluminum Surface Treatments
- Varnishing
- Corrosion Prevention
- Refining Operations
- Chlorine Electrolysis
- Electric Oil Import
- Erosion
- Metal Planting on Plastic